Make an easy $100 with Aquaponics

 Easy way to produce plants locally.

I just got done removing $100 worth of plants from my 1 gallon perlite pots that have been sitting in my aquaponics bed. I grew ~7 new Triple Crown Thornless blackberry plants, if you were to buy brand new would cost at least $10 per plant. I had 3 goji berry plants & 6 Black Elderberry plants grow as well. Easy way to get $100 of plants for barely any time spent. Here is how to do it, #1 Fill up a plastic pot with perlite (might have to block the holes at the bottom with big rocks). #2 Place that pot in your aquaponics bed, which allows the water to wick upwards. #3 Cut 6-9″ pieces and stick them ~ halfway into the perlite. You can easily do this with thornless blackberry, elderberry, hydrangea & goji berry. You would need to research on other plants. #4 Wait a few months and you have a brand new rooted plant. You can pot them, or plant them straight into the garden.

Wicking Bed

Aquaponics Wicking Bed Build

Continuing on with my stocktank aquaponics build. Today I finished one of the wicking beds. The bottom layer is lava rock, then 2 inches of perlite & top it off with soil.
 
The water pipe goes down a drain pipe to the bottom layer. The drain is surrounded by a 1 gallon plastic pot with slits cut in it.
 
I started sunflower seeds on this, hoping to get some microgreens. I covered the top with plastic to help germinate those.
 

Planting Thornless Blackberry, Aquaponics Lettuce, Smothering Weeds with Plastic

This video shows the progress made today, 30 plants were planted (blackberry, goji berry, grapes). I am planting a new row in the grass, I dig a hole, place the plant and then cover with cardboard & woodchips. I am prepping the carrot bed by covering the area with plastic & sealing the ends so that it will heat up the area to sprout weed seeds & then die. The aquaponics system has sprouted lettuce and the garlic has sprouted to be used as chives. All in all a productive day!

Big And Small Goldfish

Big And Small Goldfish

Big And Small Goldfish Intro. for Stock Tank Aquaponics | Farming Seattle

This episode, I show all of my progress on the Stock Tank Aquaponics system. I had to do a few things in order to get ready for the goldfish.

1. Added 6 legs to each end of the grow bed. Since this bed is over 1000lbs I didn’t want it to crack the stock tank. I added 4×4 legs that were braced with 2×4’s and wood screws.

2. Going to install a bigger bell siphon intake valve, after some guidance it seemed a lot better to have a 1″ inner pipe on the bell siphon since the bed will be holding a lot more water. In my next video i’ll show that installation.

3. Added outdoor electrical plug, this allowed easy wiring for the pond pump, only 20ft away from the outlet.

4. Added Goldfish! Bought 20 small / 20 large feeder goldfish ~ $10. I set these guys in the water for ~10 minutes (should have been 30). Some seemed shocked, I think next time I will do the full 30 minutes, then slowly add the aquaponics water.

Products used in video:
1″ Banjo PVC Bulkhead: http://amzn.to/2DAs1I5
2.25″ Hole Saw: http://amzn.to/2Di4TQC
Pond Liner 13×10: http://amzn.to/2Ffbvxy
Pond Pump 1000GPH: http://amzn.to/2DyxU8C
PVC 3/4″ Valves: http://amzn.to/2DxoOJa

Support us! Just by shopping on Amazon through this link: http://amzn.to/2sVAP8l

Lava Rock Grow Bed Construction

 Continuing with my 300 Gallon Stock Tank Aquaponics system.

This video shows finishing up the grow bed which involves washing a lot of lava rock, installing a uni-seal, bell siphon & putting the pond liner in place.

 

Products used in video:
1″ Banjoo PVC Bulkhead
2 1/4″ Hole Saw
Pond Liner 13×10: http://amzn.to/2Ffbvxy
 
How to wash lavarock – Drill a bunch of holes in a bucket, load some lava rock & dunk that bucket and rock in a garbage can full of water. Do this 3-4 times while rocking the bucket while the water drains. At the end, rinse with a hose to clear out as much lava sand as possible.
 
Drill a hole with the holesaw, clean it up with the rasp & razor blade. Put the rubber pond liner down over the hole & cut a clean hole with the razor blade.
 
Next, you will want to arrange the pond liner so that it is pushed against the bed, then load in washed lava rock to the top. You might want to test your bell siphon before fully loaded.
 
Bell siphon – I’m using a 1″ PVC pipe about 10″ tall, with a 2″ PVC and cap about ~12″ tall with holes drilled at the very bottom. I will probably need to do some adjustment because it wasn’t siphoning very well.
Pond

Stock Tank Aquaponics, Grow Bed Construction

Stock Tank Aquaponics grow bed.

This bed is 6’x3′ by ~ 10″ tall. It is constructed with 3- 4×4’s 1 sheet of plywood & 8 – 2×4’s. I go through the process of building the base, walls & show each step along the way.

At the end I finished with putting a drain hole in one end of the bed which will have the bell siphon.

This build took about 2 hours, getting interrupted of course, next step is to put in the pond liner, cut out the spot for the drain & attach all of the fittings.

Tools Used:
Dewalt Circular Saw: http://amzn.to/2qek1ZU
Dewalt Impact Driver: http://amzn.to/2C7olvO
1 1/2″ spade bit: http://amzn.to/2CoO332

Materials list Used for grow bed (Home Depot):
15/32″ PLYWOOD – $20.65
8 – 2X4-92 5/8″ STUD – $23.12
2″ X 10′ PVC40 $8
3/4″ PVC 90 elbows: http://amzn.to/2CpMeCP
3/4″ PVC valves x 2 – http://amzn.to/2DI6v2U
2 1/2″ exterior screws: http://amzn.to/2CoClW0
2 – 3/4″ male to slip PVC: http://amzn.to/2Csd7oY
3/4″ PVC Bulkhead: http://amzn.to/2EvPI3Y
2″ PVC Cap: http://amzn.to/2CAhJqA
3/4″ PVC 45 elbows: http://amzn.to/2CtA2jy
3/4″ PVC T fitting: http://amzn.to/2CBWsgv
Pond Liner: http://amzn.to/2CvAJJe